Products Finishing

SEP 2018

Products Finishing magazine is the No. 1 industrial finishing publication in the world. We keep our readers informed about the latest news and trends in plating, painting, powder coating, anodizing, electrocoating, parts cleaning, and pretreatment.

Issue link: https://pf.epubxp.com/i/1018703

Contents of this Issue

Navigation

Page 41 of 59

PFonline.com/zones MARK JOZEFOWICZ Reliant Aluminum Products Mark is the vice president of technical services for Reliant Aluminum Products. Visit reliantaluminumproducts.com. Solving White Spots on Black Anodized Parts Q. I am having a problem with white spots on my black anodized parts. How can I prevent these? A. White spots on black anodized finishes are a common industry problem. There are a variety of reasons why they might occur. The fix, if there is one that you as the anodizer can implement, depends on the cause. You may be able to figure out the cause by answering a few ques- tions and performing a few tests. Can the white spot be wiped off, leaving what looks like an acceptable finish? If the answer is yes, then the spot is likely due to precipitated salts, probably from the seal. These spots occur at imperfections in the coating, and the effect is exacerbated by small galvanic-induced electrical currents. Coating imperfections are often due to unwanted inclusions in the aluminum, physical microridges (machined areas) or sharp edges on the part. To mitigate galvanic effects, make sure the load bar is electrically insulated from the tank wall. If possible, use an aluminum rack, or, if it must be titanium, try to reduce the surface area of rack relative to that of the parts on the rack. Sacrificial anodes (magnesium rods) can be hung from the work bar while the parts are being dyed and sealed. You might also try a post-anodize nitric acid rinse (10 percent), as this may help to passivate areas of imperfection while at the same time improving the color quality. If the spot can't be wiped off, what is its shape? A microscope or magnifying glass may be helpful to deter- mine this more easily. Round spots are likely the result of either surface contamination or small popped blisters. You can identify blisters by determining if a coating is present at the spot. A quick test is to apply a drop of acidi- fied copper solution ( about 1 N hydrochloric acid with about 10 g/l copper sulfate) to the spot. If no coating is present, the spot will turn red within a few minutes. Blisters occasionally occur on heat-treated 7075 alloy and sometimes 6061. Blistering occurs during the anodize step, even though the spot may not show up until the part is dyed. Metal quality may be the problem here, but you also should check to see that your rectifier is operating properly. The ripple should be near 5 percent or less. Some have suggested slowing the anodize ramp rate and reducing the current density. If your power supply gives you the option, switching to a pulse electrical program is recommended. If you have determined that the round spots are not blisters, they may be the result of residue that was not adequately removed by your cleaner. Surprisingly, some residues can survive the anodize step and inhibit dye from picking up. This may be a chronic problem with one customer's parts. You might test a load by flash anod- izing followed by flash etching, then anodize and process normally. If the load looks good, you might want to focus your attention on your cleaning operation. Another source of surface residue may be small particles of mold in your anodize rinse that stick to the surface. This sometimes happens when anodizing addi- tives are used. If this is the case, you should change out the solution and thoroughly clean your rinse tank. A third source for this type of white spot may be the presence of alkali particles floating around in the air and adhering to the anodize surface while a load is being transferred to the dye or electrolytic coloring tank. Such particles become airborne when a load is taken out of the etch tank or when blind holes are cleared of residual caustic using pressurized air. To avoid this problem, you may need to take a critical look at your ventilation and minimize the amount of time an anodized load is hanging in the air. White spots that are not round are usually the result of entrapped anodize acid in tiny pits, cavities or grooves. Pits may be due to unwanted iron-containing inclusions in the metal that are etched out during the anodize step. Cavities may be due to the porosity of cast aluminum, which includes Mic 6 jig plate. Tiny grooves may occur on machined surfaces. Anodizing can open up surface or near-surface defects, leaving voids that can be very difficult to rinse clean. As a result, dye pickup will be inhibited in the area where any acid remains. Usually the acid oozes out of the pit or cavity while in the dye tank, forming irregular shaped spots, including comet tails. For this kind of white spot, the focus must be on the post- anodize rinse. A 30- to 60-second rinse in 5-10 percent nitric acid followed by a fresh water rinse works as well as anything else I've tried to eliminate this problem. 40 SEPTEMBER 2018 — PFonline.com ALUMINUM ANODIZING C L I N I C White spots that are not round are usually the result of entrapped anodize acid in tiny pits, cavities or groves.

Articles in this issue

Links on this page

Archives of this issue

view archives of Products Finishing - SEP 2018